AGTOS is highly active and involved in a multitude of new and exciting topics. Visit our newsroom often to stay informed!
Recently, we had a short visit from a delegation of leading foundry employees from China. It was a pleasure and honor to be able to present our company and ...
At the booth of our representative TAA, the exhibition team informed about AGTOS turbines and shot blasting machines. The exhibition took place from the 27th to 30th November 2018 in Shanghai.
Constant blasting parameters are essential for solidification processes. For this reason, the amount of abrasive inside the blasting process should be measured. The sensor measures the abrasive amount and can transfer it as an analogue standard signal (0-10 V) to a standard PLC control.
For the first time AGTOS is present at the Metal China exhibition in Beijing from the 16th to 19th May 2018. At the booth of our representative TAA, the largest Chinese abrasive manufacturer, visitors will see a rubber belt tumble blast machine as well as a high-performance turbine TA 4.6 and a model of a steel mill.
The jury has decided: The ROPA Tiger 6 received the "Red Dot" Design Award 2018. The panel of experts only awards the internationally recognized seal of quality to products that impress with their innovation combined with a high design quality...
For the first time AGTOS will attend the Wagner Symposium: Powder coating, wet painting, galvanizing 2018 in Rawa Mazowiecka, Poland
Together with SLF Oberflächentechnik GmbH, the colleagues of AGTOS Polska will be present at the event from 25th to 27th April 2018.
For the first time, the topic of galvanizing processes will be presented during the symposium in addition to powder coating and wet painting.
Wagner, one of the world's leading manufacturers of surface coating equipment and systems, has been organizing this event for over ten years.
A shot blasting machine marketed for the first time in the European Economic Area must comply with the legislation and with all applicable safety and environmental requirements. As with other products, the manufacturer of a blasting machine with the CE mark confirms that the product complies with the relevant EU directives, the compliance is mandatory.
At the EUROGUSS exhibition, which took place from 16th to 18th January in Nuremberg, it became official. Handtmann Leichtmetallgießerei Annaberg GmbH ordered a wire mesh conveyor shot blast machine from AGTOS.
At this year's FABTECH our partner OCEAN exhibited the OCEAN BLASTER for the first time. This special roller conveyor blast machine for profiles has convinced many customers in many countries worldwide. Accordingly, the interest of the visitors was very high.
Recently the employees of AGTOS moved into the new extension of the AGTOS office building in Emsdetten. After a construction period of one year, the extension makes a better arrangement for the technical and commercial departments of the company.
Technical springs are used in many shapes and sizes. Since they are heavily loaded, the surfaces have to meet the highest demands. AGTOS has already designed and built a large number of shot blasting machines for the sector of spring manufacturers. The new brochure presents solutions and gives suggestions. It is available in several languages.
The old church clock in the village of Laer in the Münster region became its own house. In 1891 the clock was built in Recklinghausen and first replaced in 1994. The workgroup of the home team placed the clock into stock and now, with the aid of many helpers, allowed the new commissioning of the mechanics. Previously, the parts were carefully cleaned using blasting technology.
Studying and completing an apprenticeship at the same time? This sounds very stressful for many people. “It is purely a question of organization”, says Marius Lembeck. He is about to graduate from his dual Bachelor's degree in mechanical engineering at the University of Applied Sciences in Münster and can look back on eight fully-packed semesters.
Together with 8 other companies, AGTOS was exhibiting on the joint stand of the VDMA in hall 6. Many customers, mostly international, were searching for information about new developments in the blasting technology.
Special attention was given to the exhibited drum shot blast machine. Additionally, a jury selected this machine to be a highlight of the fair and marked it with a banner.
Recently, a wire mesh belt shot blast plant has been successfully installed for the automotive supply industry in the USA and handed over to the costumer. Mario Hintzen and Julian Klemm from the AGTOS team are pleased about the good team work with the costumer.
A large shot blast plant is currently being installed in a foundry in Turkey again. We are talking about a continuous overhead rail shot blast machine with 4 turbines each with 30 kW drive power. It can treat work pieces and work piece hangers up to a width of 1,70 m and a height of 2 m. We are very happy about the good installation progress in this German-Turkish project!
Interested plant managers and operators recently visited our facility in Emsdetten. On this occasion they were informed about the advantages of pre-blasting casted work pieces with the AGTOS Ricochet blaster.
Sales engineer Andreas Sterthaus (2. f.l.) presented the concept and was able to convince our guests with some blasting trials. This machine is one of several AGTOS shot blast machines which are available for testing purposes.
Excitement caused by technology. From now on, we can present brand new models of our demonstration machines to our visitors. After the installation of a rubber belt tumble shot blast machine of type MG 0090, the newest hanger-type shot blast machine of type HT 11-13 is now also ready for testing...
During the fair Euroblech in Hannover from 25 to 29 October 2016, our fair team met many international visitors.
During the AGTOS Sales Days, the Sales Department informed our domestic and foreign sales partners about new developments in our company and the blasting technology.
Recently, two apprentices from AGTOS received their official final certificates. Antonius Heitmann, CEO, was very glad to hand out the certificates to these staff members and warmly congratulated them on passing their exams.
On 25 and 26 November 2015, professional experts and decision-makers from the industrial painting technology met for the congress “besser lackieren.” in Bad Neuheim in order to discuss about novelties in the areas of innovation, performance, efficiency, ecology and social activities which are closely linked with the painting process and to exchange personal experiences.
Noise is an important topic for many users of blast machines. That is why AGTOS places special emphasis on professional advice during the project phase.
AGTOS took part in forum for agricultural and construction machinery called ”DFO Land- und Baumaschinen Forum“
The first forum for agricultural and construction machinery called “DFO Land- und Baumschinen Forum” took place in Melle near Osnabrueck on 29/30 September 2015.
We are very glad that our customer ROPA has made a movie about the pretreatment and coating of constructions for their products.